InfinityBurnout FurnacesTMOPERATOR’S MANUALIJ15813 02/111–800–626–5651 1–502–637–1451www.whipmix.comInfinity is a trademark of Whip Mix®©2011 Whip Mix
PROGRAM AND OPERATE – ONE STAGE PROGRAM (Figure 1)9OPERATION1. Turn the power switch on.2. Press PROGRAM NUMBER. Use to display the desired
PROGRAM AND OPERATE – ONE STAGE PROGRAM (Figure 1)9OPERATION1. Turn the power switch on.2. Press PROGRAM NUMBER. Use to display the desired
OPERATIONPROGRAM AND OPERATE – THREE STAGE PROGRAM (Figure 1)111. Follow Two Stage Program, Steps 1 – 4.2. Press ENTER / REVIEW. STAGE 2 lig
OPERATIONPROGRAM AND OPERATE – THREE STAGE PROGRAM (Figure 1)111. Follow Two Stage Program, Steps 1 – 4.2. Press ENTER / REVIEW. STAGE 2 lig
OPERATIONREVIEW A PROGRAM (Figure 1)131. Turn the power switch on.2. Press PROGRAM NUMBER.3. Press to select the program number to be revie
OPERATIONREVIEW A PROGRAM (Figure 1)131. Turn the power switch on.2. Press PROGRAM NUMBER.3. Press to select the program number to be revie
NIGHT TIMEDELAY STARTOPERATIONSAMPLE ONE STAGE PROGRAM(To be completed and ready to cast in 24 hours) HEAT RATETEMPHOLD TIMESTAGE 1STAGE 2STAGE 3STAGE
NIGHT TIMEDELAY STARTOPERATIONSAMPLE ONE STAGE PROGRAM(To be completed and ready to cast in 24 hours) HEAT RATETEMPHOLD TIMESTAGE 1STAGE 2STAGE 3STAGE
ERROR CODESNOTE: “Beeps” occur when the Error Code appears on the Main DisplayERRORCODEDESCRIPTIONPROBABLE CAUSEINVALID ENTRY ERROR: STAGE, HEAT RAT
ERROR CODESNOTE: “Beeps” occur when the Error Code appears on the Main DisplayERRORCODEDESCRIPTIONPROBABLE CAUSEINVALID ENTRY ERROR: STAGE, HEAT RAT
1Introduction ...2 Warranty ...
19CAUTION: The INFINITY should be serviced only by qualified service technicians. Be sure to unplug the power cord and wait for the furnace to cool b
19CAUTION: The INFINITY should be serviced only by qualified service technicians. Be sure to unplug the power cord and wait for the furnace to cool b
1. Remove the back panel of the furnace.2. Remove the nuts which hold the heating plate wires to the power terminals and straighten the heating pl
1. Remove the back panel of the furnace.2. Remove the nuts which hold the heating plate wires to the power terminals and straighten the heating pl
1. Remove the front panel (Figure 5).2. Note and record the color and location of each wire on the thermocouple terminals located on the Main PC Bo
1. Remove the front panel (Figure 5).2. Note and record the color and location of each wire on the thermocouple terminals located on the Main PC Bo
1. Remove the bottom front panel and the upper and lower rear panels of the furnace. (Note the position of the vent louvers on the rear panels.)2.
1. Remove the bottom front panel and the upper and lower rear panels of the furnace. (Note the position of the vent louvers on the rear panels.)2.
27SPARE PARTS LISTDESCRIPTION 115V 220/230V Power Cord Kit–Japan & U.S. 15288 N/APower Cord Kit–Australia N/A 23206Power Cord Kit–England N
27SPARE PARTS LISTDESCRIPTION 115V 220/230V Power Cord Kit–Japan & U.S. 15288 N/APower Cord Kit–Australia N/A 23206Power Cord Kit–England N
1Introduction ...2 Warranty ...
PROGRAM CARD FORMSSTAGE 1STAGE 2STAGE 3STAGE 4 HEAT TEMP HOLD RATE TIMEProgram # Metal(s)STAGE 1STAGE 2STAGE 3STAGE 4 HEAT TEMP HOLD
PROGRAM CARD FORMSSTAGE 1STAGE 2STAGE 3STAGE 4 HEAT TEMP HOLD RATE TIMEProgram # Metal(s)STAGE 1STAGE 2STAGE 3STAGE 4 HEAT TEMP HOLD
InfinityBurnout FurnacesTMOPERATOR’S MANUALIJ15813 02/111–800–626–5651 1–502–637–1451www.whipmix.comInfinity is a trademark of Whip Mix®©2011 Whip Mix
SPECIFICATIONSINFINITY M–30 INFINITY L–30Electrical115V 50/60Hz 1150W220/230V 50/60Hz 1150W115V 50/60Hz 1610W220/230V 50/60Hz 1610WCapacity 8-1 3
SPECIFICATIONSINFINITY M–30 INFINITY L–30Electrical115V 50/60Hz 1150W220/230V 50/60Hz 1150W115V 50/60Hz 1610W220/230V 50/60Hz 1610WCapacity 8-1 3
5Figure 1INFINITY M–30 AND L–30 IDENTIFICATION 13101198765124321Front PanelHeating ChamberVentTubeKEY PARTS IDENTIFICATION AND EXPLANATION220/230KEY P
5Figure 1INFINITY M–30 AND L–30 IDENTIFICATION 13101198765124321Front PanelHeating ChamberVentTubeKEY PARTS IDENTIFICATION AND EXPLANATION220/230KEY P
UNPACK AND SET–UPINSTALLATION71. Unpack the contents of the box. Remove the following materials: A. Vent Tube – Remove from bubble wrap and insert i
UNPACK AND SET–UPINSTALLATION71. Unpack the contents of the box. Remove the following materials: A. Vent Tube – Remove from bubble wrap and insert i
Comments to this Manuals