Whip Mix FireLite Specifications download pdf (Page 55)

Replacement Parts

Vac-U-Mixer

Drive Nuts and Chucks

Whip Mix driving motors provide

two basic speeds. High speed, at

1,725 rpm, is recommended only for

vacuum-investing with the 200 mL

Vac-U-Spat. Because of its small

paddle diameter, the Vac-U-Spat

gives the most uniform results with

all inlay investments with high speed

spatulation.

Low speed, at 425 rpm, is

recommended for all Vac-U-Mixers

when spatulating gypsum materials,

alginates and large quantities of

investments. The Vac-U-Mixer Plus

provides only low speed. But the

Combination Unit has two drive

speeds: the rear Drive Chuck #6108

is the high speed at 1,725 rpm,

and the front is the low speed at

425 rpm. Drive Nuts on the mixing

units and corresponding drive chucks

on motors have been designed to

prevent the inter change of a mixing

unit between these two speeds.

Also, the directions of rotation of

the drive chucks for these speeds

is opposite. The high-speed drive

chucks of the Combination Unit and

the discontinued Vac-U-Vestor require

a left-hand thread for the paddle

shaft and drive nut. The low-speed

drives of the Combination Unit and

the Vacuum Power Mixer Plus need a

right-hand thread for the paddle shaft

and drive nut.

It is important, therefore, that the

proper drive nut is specied whenever

a mixing unit is ordered. And when

adapting a mixer already in use, the

thread direction must be considered

– sometimes the entire paddle

assembly must be changed.

Item No. Description

09091 #6375 Slotted Drive Nut for Operation with Combination Unit or Vacuum

Power Mixer – R.H. Thread

09113 #4109 Friction Grip Drive Nut (for 200, 300, and 500 mL Size Only) for

Operation with Vac-U-Vester and Combination Unit – L.H. Thread

09105 #6865 Slotted Drive Nut (for 1200 mL Vac-U-Mixer or #6800 Mechanical

Mixer) for Operation with Combination Unit or Vacuum Power Mixer –

R.H. Thread

15555 #6393 Drive Nut for Operation with Handy-Holder on Combination Unit or

Vacuum Power Mixer – R.H. Thread

Plastic Tubing and Connections

09156 #5700 Plastic Tubing, 2-1/4 ft. with Plastic Trap, Trap Cap and O Rings

09172 #5701 Metal Trap Cap with O Rings #1 and #2

09180 #5703 Gauze for Plastic Trap (Pkg. of 6)

09199 #5704 Retainer Spring

09202 #5705 Plastic Trap with Retainer Spring and Gauze

09211 #5709 Plastic Tubing – 5 ft. Length

16721 #5707 Plastic Tubing – 2-1/4 ft. Length

07366 #4008 O Ring #1-5/16" O.D. for Tip of Trap Cap (Pkg. of 6)

07374 #5702 O Ring #2-7/16" O.D. – Fits Inside Trap Cap (Pkg. of 6)

Parts for Vac-U-Mixer

Note: Two O Rings #1 (#4008) are installed on paddle shaft of all

sizes except the #7600 which requires O Rings #2 (#5702).

875 mL #6600

Stainless Steel

Paddle #6406

Stainless Steel Paddle

#4458 (Alginate)

#4455 (Gypsums)

Stainless Steel

Paddle #6506

(Gypsums)

Stainless Steel

Bowl #7602

Drive Nut #6393

(used with Handy Holder)

200 mL #6400

Drive Nut

#6375

Plastic Lid

#6401

O Ring #4

(#4006)

Plastic Bowl

#4002

300 mL #4450

O Ring #4

(#4006)

Drive Nut

#6375

Plastic Lid

#6401

Plastic Bowl

#4452

Plastic Bowl

#6502

500 mL #6500

Drive Nut

#6375

O Ring #6

(#6505)

Plastic Lid

#6501

1200 mL #7600

Drive Nut

#6865

Metal Lid

#7601

O Ring #8

(#7605)

Stainless

Steel Paddle

#7606

Stain-

less Steel

Paddle

#6606

Plastic Bowl

#6602

O Ring #6

(#6505)

Plastic Lid

#6501

#5701

#5705 #5706

#5702

#4008

#5704

#5703

#5700

Equipment

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 88 89

Comments to this Manuals

No comments

Whip Mix FireLite Specifications Page 55

Comments to this Manuals

Related products and manuals for Water heaters & boilers Whip Mix FireLite